|
|
Interior Hallway
Systems
Janus Advantage Features Innovative
PRODUCT DESIGN with hemmed edges for smoother surfaces that you
can see and feel. Hems on the starter angle, mid span, kick plates, corner
guards, side channels and angels give the hallway a completely finished
look and eliminate hazards that can occur with exposed edges. This sleek
intergraded system design increases the door integrity making it stronger
and sturdier.
Click here to purchase or price
A
supplemental PROTECTIVE PACKAGE comes with Janus Advantage
Systems that keeps your hallway looking nice even when tenants run into
the walk and bang the corners. The following items are all part of the
protective package that helps you obtain a higher return on your investment
by keeping your facility looking new:
•Secure Wall - The
non-load bearing wall divider is manufactured in 20" wide section
that locks together without he use of exposed screws. It is installed
vertically to minimize dust. All channels and angles necessary to install
securewall are included. Colors available are glossy white and white.
•Unit Partition - Like the hallway securewall,
unit partition is manufactured in 20" wide sections and installed
vertically. This 26 gauge wall is much more economical than sheet rock
or wooded studs while it still provides the necessary level of security
you come to expect in a wall. All channels and angles necessary to install
the unit partition are included.
•Corawall Hall Partition - An alternative to corrugated
securewall, these 12" self aligning paneled interlock so that there
is no exposed screws or edges except where attached at the top channel.
Top and bottom channel provides additional strength for supporting panels.
An added insurance, the Protective Package is available to keep these
walls dent and ding free once installed.
•Midspan - This hemmed 20 gauge channel further
enhances the strength and integrity of our hallway systems. Offering additional
support without having to utilize load bearing walls, this bracing is
available in gloss white, white or galvalume.
•Roll-Up Frames - Essential to the structure of
the self supporting system, the roll-up frame is designed to maximize
strength and integrity while minimizing space. The 2" return offers
stronger frame suited for roll-up door or Z-Frame swing door installations.
Single roll-up frames 6" to 12" and double roll-up frames 12"
to 24" are made of hot dipped galvanized 20 gauge steel. Glossy white,
white or galvalume are the colors in which these frames are available.
All bases, channels and angles and fasteners necessary to secure the frames
to the exterior walls, floors and/or ceilings are included with the frames.
•Kick Plates - Kick plates are installed to protect
the bottom of your hallway walls from scratches and dents that may occur
as tenants move their belongings into a unit. These 20 guage galvalume
pieces are furnished hemmed on both the top and the bottom. Even though
this is typically manufactured 12" tall in 10'0" lengths, custom
sizes can be accommodated. The value of the kick plates is tremendous
considering the wear and tear they take in order to keep the self storage
facility attractive long after "the new" has worn off.
•Corner Guards - Corner Guards are utilized to
help protect your hallway corners from scratches , dents and dings that
occur as tenants transports their belongings down the hallways to their
unit. As a standard component of the Janus hallway system, the 3"
x 3" - 20 gauge corner guards are hemmed on both sides and available
in galvalume, white or glossy white. The optional mitered corner guard
that further enhances the aesthetics of the hallway system is available
for corners when an extended turning radius is desired.
•Mo Caps - Mo Caps are little plastic nipples that
cover the tips of tek screw that might be left exposed. While the Janus
system is designed to eliminate exposed screw ends, sometimes unusual
or extreme circumstances might cause the screw ends to be exposed. Therefore,
Mo Caps are standard with our hallway systems.
•Mesh - A cost effective method od keeping your
tenants possession safe is the mesh and mesh angle stretched over the
storage units. The 2" x 2" - 16 gauge mesh provides security
between units while still allowing for adequate lighting and air flow
inside each unit.
•
Soffit - Hallway, light and entry soffit make finishing
the ceiling and entrance of a storage facility economical and yet attractive.
The different soffit types provide a clean finished look to the hallway
and maximize lighting which is appealing to potential customers.
•Corrugated
Swing Door - Our swing door has revolutionized the industry.
With re-enforced solid-square tube cross braces and 3" wide vertical
stiles, this door is far superior to any others in the industry. Our patent
pending latch with a magnetic slide that is designed for an optional cylinder
is factory installed on the swing. The silicone polyester paint on the
doors is warranted not to chalk, chip, fade or peel, and also carries
a 20 year film integrity warranty. Available in any of the 26 gauge colors,
the system and swing door make an attractive compliment or alternative
to roll-up doors.
•Headers
- Manufactured out of 20 gauge material, the header enclose the area between
the top of the door and top of the hallway system creating a smooth contemporary
look to the flush hallway system. It provides for a clean transition from
wall to ceiling when using light sofit or solid ceiling and maximizes
light reflection. All angle and fasteners required for install are included
in the price of the header panel. Colors available are white, glossy white
and galvalume.
•Corrugated
Filler Panel - An economical alternative to a flush header is
the corrugated filler panel. This 26 gauge component is used in the same
manner as the flush header to enclose the space between the door and top
of the hallway. However, unlike the flush header panel, the filler panel
can be manufactured in any of the door colors to accent the hallway or
roll-up doors. All channel and angle necessary to install the filler panel
is included. Top angle is considered an accessory. |
|
|
|
|
|
|
The
3" Wide Vertical Stiles provide strength and better support
for the door. |
The
Patent Pending Latch has a magnetic slide designed for an optional
cylinder and is factory installed. |
The
Square Tube Cross Bracing reinforces the door and provides extra
strength. |
|
|